Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. How to make storage shelves: All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves.

This charging station looks just like those expensive ones you see at department stores, but it will cost you much less. Actually, if you have a 2X4 on hand, it won’t cost you anything. You just need to cut a piece of your board, measure the hole that you need to fit your phone and then stain the board. You can build it to fit your phone no matter what type it is, so there are no worries of the phone not being secure while it’s charging.
This is not exactly a tutorial, but a guide to some really cool woodworking projects. Although we are not teaching you to make anything, we are always here to help. Feel free to ask your queries in the comments in case if you face any issue while working on any of these projects. Also, tell us how much you liked this article. Did you enjoy reading it? Did you work on any of these projects, and if yes, how was your experience? You are also welcome to share any images of your completed woodwork projects.
If you have ever wanted to build your own furniture or home decor, I have a wonderful treat for you. I’ve found 50 home decor and furniture ideas that you can make from 2X4s. The wonderful thing about this project list is you don’t have to have a lot of woodworking experience or expensive supplies to create beautiful pieces for your home. 2X4s are really cheap. In fact, they’re among the cheapest pieces of lumber that you can find. Head off to Lowe’s or your favorite home improvement store and you’ll find that these boards are only about $3 for an eight foot board. You can make so many wonderful things with those inexpensive boards, and I’m going to show you how.

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.

How great is this little Jeep? Whether you use this as a handmade toy or you want to display it, it’s a beautiful project and one that you can DIY! This one will take you a bit of time, but imagine how it will look displayed in your home. You can leave it plain for a rustic look or paint it however you want. If you’ve ever wanted to build your own Jeep – not one that you can drive obviously – this is the perfect 2X4 project.
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
Assemble the extension frames using nails or screws and a little glue. Note that one side of the frame (G) is 1/4 in. narrower than the other (H). That creates a recess for the 1/4-in. plywood back (S). Next, skin the cabinet sides with 1/4-in. plywood (Photo 1). After spreading glue, I tacked the plywood in place with a couple of brad nails and then weighted it down with paint cans. Also glue the fillers (E) into the recesses at the top and bottom of the cabinets. Fillers give you a solid core to drive screws through when you screw the cabinets to the base and top—without them, screws might pop right through the flimsy 1/2-in. particleboard of the cabinets.
This outdoor couch will take a few 2X4s – about 11 of them to be exact but at less than $10 each for the boards, it will still cost you less than anything you can get at a patio or furniture store. And, it’s a really sturdy couch. The best part? You can completely build this couch in less than four hours. Once you’ve finished, just add those homemade couch cushions and you’re all set to relax in the backyard.
This potting bench is the perfect addition to your garden area and it’s a really easy build from those 2X4s. It has space for everything! If you’re an avid gardener then you need a sturdy bench to work up those seeds and prepare them for planting, right? This one is really sturdy and really cheap and easy to build. Plus, it just looks really good sitting next to the house or on the deck.

This mirrored coffee table is sure to be a great addition to your living room. It’s also a really easy project to build and the end result is absolutely stunning. You’ll need an old mirror, maybe from a dresser that you don’t need any longer. This one lets you use up some of those 2X4s and repurpose some old furniture at the same time. It should cost you less than $50 to make – as opposed to buying it in a furniture store for a couple hundred.

×