In just a few minutes, you can turn those 2X4s into beautifully rustic picture frames. These little frames are perfect for holding your most precious images and they are all so very easy to make. You can use those scrap pieces of board from other projects and create a frame that is perfect for gift giving. Make them as simple or as fancy as you like.
You can simply check out these amazingly genius 60 Easy DIY Wood furniture projects that involve the mind-blowing tips and tricks to get crafty with old wood for some amazing DIY furniture recoveries! The mind-blowing DIY furniture samples given in the collection will also leave a great spell on the wood crafting lovers as they are amazingly creative, super functional and smartly made!
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.

Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
You only need a couple of 2X4s to build this beautiful farmhouse style entry table. You could also use this as a console – however you use it, you’re going to love the farmhouse quality. It’s such a simple rustic design and you can build the entire table, even if you don’t have any other materials, for $20 or less. Imagine having this amazing table for less than $20!
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
If you tend to love woodworking projects, this workbench is certainly something that you should build. You can get all of the supplies you need to make it for around $20, which is much cheaper than buying an already made workbench. It’s cheap and nothing that you would expect to see in a high end workshop, but it’s also sturdy and definitely gets the job done.
First, screw the face frames of the two cabinets together. Drill pilot holes and drive screws through the lower face frame into the upper. Then lay them on one side and hold a straightedge across the fronts of the face frames to be sure they form a straight, flat surface. I had to slip a strip of cardboard between the two cabinet boxes to get the face frames aligned.
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.

Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
If you’ve ever dreamed of having a farmhouse style bedroom, this 2X4 nightstand is a must. It’s such an easy little stand to build and it really does give off that great rustic country vibe. You only need three 2X4s to make it, too – and at less than $10 each, that’s way less than you would pay for a designer farmhouse nightstand. You can afford to put one on each side of the bed!

I have a wine rack but it’s nowhere near as gorgeous as this one. Plus, mine doesn’t hang. This one hangs on the wall to keep it out of the way and it’s the simplest wine rack you will ever think about building. You just treat your wood however you want – stain, paint, etc. – and then drill holes, strategically placed of course, to hold your wine bottles. This is perfect if you need a wine rack but don’t really have room for something big and bulky.
With technology changing so fast, it didn’t seem smart to sink a lot of money into a TV stand. But inexpensive stands didn’t have the features I wanted: enclosed storage and lots of shelves for electronic components. This stand gives me those things, plus it’s rock solid. Some inexpensive stands are rated to support 75 lbs. or less. This thing would hold a V-8 engine block. It’s sized for a 42-in. TV, but you could easily make it bigger by spacing the cabinets farther apart or choosing wider cabinets. It’s taller than most stands, which may be good or bad, depending on your situation.
×