Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
This bench can be made from reclaimed wood that you’ve had left over from other projects. It’s a really simple bench to build and is perfect for the mudroom. If you don’t have a mudroom or room near the backdoor to put it, place it on the porch. It’s the perfect place it sit and take off muddy shoes and you can store baskets underneath for holding shoes or scarves and mittens when it’s cold outside.
This mirrored coffee table is sure to be a great addition to your living room. It’s also a really easy project to build and the end result is absolutely stunning. You’ll need an old mirror, maybe from a dresser that you don’t need any longer. This one lets you use up some of those 2X4s and repurpose some old furniture at the same time. It should cost you less than $50 to make – as opposed to buying it in a furniture store for a couple hundred.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
Assemble the extension frames using nails or screws and a little glue. Note that one side of the frame (G) is 1/4 in. narrower than the other (H). That creates a recess for the 1/4-in. plywood back (S). Next, skin the cabinet sides with 1/4-in. plywood (Photo 1). After spreading glue, I tacked the plywood in place with a couple of brad nails and then weighted it down with paint cans. Also glue the fillers (E) into the recesses at the top and bottom of the cabinets. Fillers give you a solid core to drive screws through when you screw the cabinets to the base and top—without them, screws might pop right through the flimsy 1/2-in. particleboard of the cabinets.

Before fall comes around, you just have to make this great pumpkin décor from those leftover 2X4 scraps. These look like decorations that you can get at Hobby Lobby and other similar stores, which typically run around $50 for the set. You can make them yourself for under $5 if you have the boards on hand. Just paint them orange and add your decorations. This is such a simple project and it gives you such lovely décor for fall.
It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project.

If you tend to love woodworking projects, this workbench is certainly something that you should build. You can get all of the supplies you need to make it for around $20, which is much cheaper than buying an already made workbench. It’s cheap and nothing that you would expect to see in a high end workshop, but it’s also sturdy and definitely gets the job done.
This outdoor couch will take a few 2X4s – about 11 of them to be exact but at less than $10 each for the boards, it will still cost you less than anything you can get at a patio or furniture store. And, it’s a really sturdy couch. The best part? You can completely build this couch in less than four hours. Once you’ve finished, just add those homemade couch cushions and you’re all set to relax in the backyard.
Assemble the extension frames using nails or screws and a little glue. Note that one side of the frame (G) is 1/4 in. narrower than the other (H). That creates a recess for the 1/4-in. plywood back (S). Next, skin the cabinet sides with 1/4-in. plywood (Photo 1). After spreading glue, I tacked the plywood in place with a couple of brad nails and then weighted it down with paint cans. Also glue the fillers (E) into the recesses at the top and bottom of the cabinets. Fillers give you a solid core to drive screws through when you screw the cabinets to the base and top—without them, screws might pop right through the flimsy 1/2-in. particleboard of the cabinets.
You can never have too much storage space and this little bench gives you loads. It’s made from those 2X4s and has a great X leg look. Underneath the seat are crates, which you can also make from your 2X4s, for storing just about anything you need to store. This would be a great outdoor bench for the patio. You can use the crates to store outside toys or even things that you need when you’re grilling out. Best of all, you can build the entire thing, including stain, for around $40 or less.
If you need a sawhorse for all of those woodworking projects, this is an easy one to build. You just nail your 2X4s together to create it and since those boards are a bit heavy, this little sawhorse is rock solid. You won’t have to worry about your boards slipping when you have them on here for sawing. If you don’t have a sawhorse, and you don’t want to spend upwards of $50 to buy a pair, I strongly recommend this DIY project.
It may not be close to St. Patrick’s Day but that shouldn’t stop you from making this adorable little leprechaun’s hat. You can use it to decorate next year, and it’s made from leftover pieces of your 2X4. If you’re looking for a project to finish up those wood scraps, here it is. Just paint your wood pieces green and then stack them to make the hat. It’s easy and adorable!
Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
This mirrored coffee table is sure to be a great addition to your living room. It’s also a really easy project to build and the end result is absolutely stunning. You’ll need an old mirror, maybe from a dresser that you don’t need any longer. This one lets you use up some of those 2X4s and repurpose some old furniture at the same time. It should cost you less than $50 to make – as opposed to buying it in a furniture store for a couple hundred.
×